P1391
DTC P1391, P1392, or P1393
DTC Descriptors
DTC P1391
- Rough Road Sensor Performance
DTC P1392
- Rough Road Sensor Circuit Low Voltage
DTC P1393
- Rough Road Sensor Circuit High Voltage
Diagnostic Fault Information
Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Typical Scan Tool Data
Circuit/System Description
The rough road sensor is a vertical low G-acceleration sensor. By sensing vertical acceleration caused by rough road conditions, the engine control module (ECM) can determine if the changes in crankshaft speed are due to engine misfire or are driveline induced. If the rough road sensor detects a rough road condition, the ECM misfire detection diagnostic will be de-activated. The rough road sensor at rest output should be between 2.30-2.65 volts. During a rough road condition, the voltage output can vary between 0.5 volt and 4.5 volts. The rough road sensor is a capacitive type sensor with 3 circuits:
* A 5-volt reference circuit
* A low reference circuit
* A signal circuit
The ECM provides the rough road sensor with 5 volts on the 5-volt reference circuit and a ground on the low reference circuit. Vibration to the rough road sensor from rough road conditions in the road, provides the ECM with a signal voltage from less than 1 volt to more than 4 volts.
Conditions for Running the DTC
P1391
* The engine has been running for more than 10 seconds.
* The vehicle speed is less than 5 km/h (3.1 mph).
OR
* The engine has been running for more than 10 seconds.
* The vehicle speed is between 30-70 km/h (19-43 mph).
* The DTC runs continuously when the above conditions are met.
P1392 and P1393
* The engine has been running for more than 10 seconds.
* The DTCs run continuously when the above condition is met.
Conditions for Setting the DTC
P1391
The ECM detects that the rough road sensor output is not within range.
P1392
The ECM detects that the rough road sensor voltage is less than 0.1 volt.
P1393
The ECM detects that the rough road sensor voltage is more than 4.9 volts.
Action Taken When the DTC Sets
DTC P1391, P1392, and P1393 are type C DTCs.
Conditions for Clearing the MIL/DTC
DTC P1391, P1392, and P1393 are type C DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics Electrical Diagrams
Connector End View Reference
* Engine Control Module (ECM) Connector End Views Engine Control Module (ECM) Connector End Views
* Engine Controls Connector End Views Engine Controls Connector End Views
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Diagnostic Trouble Code (DTC) Type Definitions Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
* Scan Tool Data List Scan Tool Data List
* Scan Tool Data Definitions Scan Tool Data Definitions
* Scan Tool Output Controls Scan Tool Output Controls
Circuit/System Verification
1. Start the engine. Observe the rough road sensor voltage parameter. The reading should be between 1.1-3.7 volts.
2. If the vehicle passes the Circuit/System Verification Test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector of the rough road sensor.
2. Ignition ON, verify that the rough road sensor parameter is less than 0.1 volt.
• If greater than 0.1 volt, test the signal circuit of the rough road sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.
Important: The test lamp is used to load the circuit and may not illuminate.
3. Ignition ON, connect a test lamp between the 5-volt reference circuit of the rough road sensor and ground.
Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.
4. Test for 4.8-5.2 volts between the 5-volt reference circuit of the rough road sensor and ground.
• If less than 4.8 volts, test the 5-volt reference circuit of the rough road sensor for a short to ground or open/high resistance. If the circuit/connections test normal, replace the ECM.
• If greater than 5.2 volts, test the 5-volt reference circuit of the rough road sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.
5. Ignition ON, test for less than 0.2 volt between the low reference circuit of the rough road sensor and ground.
• If greater than 0.2 volt, test the low reference circuit of the rough road sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.
6. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit of the rough road sensor and ground.
• If greater than 5 ohms, test the low reference circuit of the rough road sensor for an open/high resistance. If the circuit/connections test normal, replace the ECM.
7. Ignition ON, install a 3-amp fused jumper wire between the signal circuit and the 5-volt reference circuit of the rough road sensor to verify that the rough road sensor parameter is greater than 4.8 volts.
• If less than 4.8 volts, test the signal circuit of the rough road sensor for a short to ground or an open/high resistance. If the circuit/connections test normal, replace the ECM.
8. If all circuits/connections test normal, replace the rough road sensor.
Repair Instructions
Important: Always perform the Diagnostic Repair Verification Diagnostic Repair Verification after completing the diagnostic procedure.
* Rough Road Sensor Replacement Service and Repair
* Control Module References Control Module References for engine control module replacement, setup, and programming