Engine Torque Specification

Main Bearing Bolts	With Aluminum Block	Jointing Torque	20
		Turning Angle	70 Degrees
	With Iron Block	Jointing Torque	20
		Turning Angle	50 Degrees
Struts/Bracing Shell	10 mm		43
	8 mm		22
Coolant Drain Plug In Block	14 x 1.5 mm		25
Main Oil Duct Screw Plug	16 x 1.5 mm		34
	18 x 1.5 mm		40
OIl Spray Nozzle On Block	6 mm		10
	8 x 1 mm banjo bolt		12
Cylinder Head Bolt	Cast Iron Block Replace, wash and oil cylinder head bolts.	Jointing Torque	30
		1st Turning Angle	90 Degrees
		2nd Turning Angle	90 Degrees
	Aluminium Block Fit New Cylinder Head Bolts Do Not Wash Away Coating On Cylinder Head Bolts.	Jointing Torque	40
		1st Turning Angle	90 Degrees
		2nd Turning Angle	90 Degrees
Cylinder Head (Valve) Cover	6 mm		10
	7 mm		15
Timing Case to Cylinder Head	7 mm		15
	8 mm		20
Oil Drain Plug	12 x 1.5 mm		25
	22 x 1.5 mm		60
Oil Pan To Block	6 mm 8.8		10
	6 mm 10.9		12
	8 mm 8.8		22
Oil Sump Lower Section To Upper Section	6 mm 8.8		10
	6 mm 10.9 Replace Microencapsulated Bolts.		12
Timing Case And Timing Case Cover Top & Bottom	6 mm		10
	7 mm		15
	8 mm		22
	10 mm		47
Front End Cover To Block	6 mm		10
	8 mm		22
Rear End Cover To Block	6 mm		10
	8 mm		22
Connecting Rod Bolts Replace, Wash and Oil Conrod Bolts.		Application Torque	5
		Jointing Torque	20
		Torque Angle	70 Degrees
Increment Wheel On Crankshaft	5 mm 10.9		13
	5 mm 8.8 Microencapsulated Bolt.		5.5
Flexplate To Crankshaft		Engine With Auto. Trans.	120
Flywheel To Crankshaft			105
Vibration Damper To Crankshaft Replace Bolt			410
Belt Pully To Vibration Damper	8 mm		22
Camshaft Bearing Cap	6 mm		10
	7 mm		14
	8 mm		20
Sprocket To Camshaft Flange		Application Torque	5
		Jointing Torque	22
Splined Shaft To Intake Camshaft		Jointing Torque	40
		Torque Angle	60 Degrees
Plug For Chain Tensioner	22 x 1.5 mm		40
Cylinder For Chain Tensioner Plunger	26 x 1.5		70
Screw-in Pin On Camshaft	7 mm		20
Nut For Screw-in Pin On Camshaft	6 mm		10
4/2-way Valve/Solenoid Valve To VANOS Housing			30
Banjo Bolt To VANOS Controller	14 x 1.5 mm		32
Plug To VANOS Adjusting Unit	22 x 1.5 mm		50
Set Screw For Hudraulic Piston On Toothed Shaft	6 mm	LEFT HAND THREAD	10
Hydraulic Line For VANOS On Oil Filter Aggregate Carrier			32
Oil Pump To Crankcase	8 mm		22
Oil Pump Cover	6 mm		10
Sprocket To Oil Pump	6 mm		10
	10 mm		47
	10 x 1 mm		25
Full Flow Oil Filter Cover	8 mm		22
	10 mm		33
	12 mm		33
Screwed On Cover			25
Oil Filter Housing & Lines On Crankcase	8 mm		22
	20 x 1.5 mm		40
Oil Line To Bearing Points & Camshaft Lubrication	6 mm		10
Oil Line For Camshaft Lubrication On Cylinder Head	8 x 1 mm	Hollow Bolt	10
	5 mm		5
Oil Cooler Pipes To Oil Filter Housing	8 mm		22
Water Pump To Crankcase	6 mm		10
	7 mm		15
	8 mm		22
Fan Clutch Coupling Nut To Water Pump		LEFT HAND THREAD	40
Thermostat Housing	6 mm		10
Bleeder Screw	8 mm		8
Intake Manifold To Cylinder Head	8 mm		22
	7 mm		15
	6 mm		10
Exhaust Manifold To Cylinder Head Coat Connections with Molycoat HSC compound or equivalent.	6 mm		10
	7 mm		20
Upper Row Of Staybolts	8 mm		22
Oxygen Sensor			55
Oxygen Monitor Sensor			55
Engine Mount To Front Axle Carrier	8 mm		22
	10 mm		47
Engine Mount To Engine Console (Bracket)	8 mm		22
	10 mm		47
Engine Console (Bracket) To Engine	8 mm		22
	10 mm		47