DIS V3.0 Installation Instruction
DIS V3.0 INSTALLATION INSTRUCTIONBefore starting this procedure make sure that you have:
1 DIS Installation 1 3.5" floppy disc (red label)
1 DIS Installation 2 3.5" floppy disc (red label)
1 DIS Basissystem V3.0 CD (red label)
1 DIS Program V3.0 CD (white label)
If you do not have all of the above software do not start this procedure. Total loading time is approximately 3 hours.
1. With the DIS at the administration screen, deactivate CD drive 1 and remove the CD caddy. Repeat this procedure for CD drive 2.
2. Switch the power switch on the monitor off.
3. Connect the keyboard to the interface in the MoDiC station drawer.
4. Insert V3.0 "Installation 1" floppy in the floppy drive. The write protect tab must be open.
5. Switch the power switch on the monitor on. After approximately two minutes the message "Insert floppy Installation 2 and press
6. Remove Installation 1 floppy and insert the Installation 2 floppy in the disc drive. Press the enter/return key. The write protect tab must be closed.
7. When the message "Insert Basic System CD in drive CD1 and press return" appears on the screen, place the Basic System CD (red label) in a CD caddy and insert the caddy into CD drive 1 (top drive).
8. Press return. This installation procedure takes approximately 30 minutes. Note: An error message may appear on the screen during this installation. Ignore this message.
9. At the end of the installation procedure, the illustrated message will appear:
10. Remove the Installation 2 disc and press return.
NOTE
Touch screen calibration will be the next operation. Touch screen calibration is a critical process that sets up the hardware and the software. Please take great care and follow the instructions.
11. The message "Please touch the bottom left hand corner will be displayed. Touch the bottom left comer and lift your finger - do not slide your finger. Wait for the message "first calibration point reached. Please touch the right hand top corner."
12. Touch the right hand top corner and lift your finger.
13. An arrow will now appear at the lower left hand corner. Touch this spot. Be careful to lift your finger.
14. An arrow will now appear at the upper right hand comer. Touch this spot. Be careful to lift your finger. Crossed lines will be displayed at the end of this step. They will disappear in a few seconds. The cursor setting may be affected if the screen is touched with a metallic object.
15. When the language selection screen is displayed, select "3 English (US)." Selection must be carried out via the keyboard. Press return.
16. You will be asked to confirm this. Confirm your selection and press return.
NOTE
The language screen inputs are mandatory. Further inputs are not possible unless the same language has been selected two times.
17. A dealer data screen is now displayed. Dealer data must be input via the keyboard. Fields 1 = dealer number, 2 = company name and 4 = address are mandatory fields. These fields must be input correctly or they cannot be exited. The qualifiers for these fields are as follows:
1. DEALER NO. AN INPUT OF EXACTLY 6 DIGITS MUST BE MADE.
2. COMPANY NAME AN INPUT MUST BE MADE OF AT LEAST 2 CHARACTERS.
4. ADDRESS AN INPUT MUST BE MADE OF AT LEAST 2 CHARACTERS.
18. Enter the required data, follow each line entered with the return key. Lines 3, 5 and 6 may be skipped by pressing the return key.
19. A screen will appear that will display all of the dealer data that you have entered. Press "Y" if it is correct. If you press "N" you will be asked which line you wish to correct. Enter the line number and retype the information. Press return.
20. The DIS start screen will now appear.
NOTE
ALL FURTHER FUNCTIONS WILL BE CARRIED OUT VIA THE TOUCH SCREEN. DO NOT REMOVE THE KEYBOARD WHILE THE TESTER IS POWER UP. YOU MAY REMOVE THE KEYBOARD THE NEXT TIME THE TESTER IS OFF.
21. The following steps will guide you through the installation of the DIS Program CD. Basissystem V3.0 must be installed before you load the program CD. The version number of the installed basic system can be displayed by pressing the "services version" button at the DIS start screen. The version of V3.0 basic system will read
"Administration 3.1.0
Basic system V3.0"
22. At the DIS start screen, activate "administration" and then highlight CD drive 1.
23. Press "deactivate CD." Remove the CD caddy from CD drive 1. Remove the Basissystem CD from the caddy.
24. Insert program CD (white label) in the caddy. The CD must be installed so that the CD label can be seen through the clear side of the caddy.
25. Carefully insert the program CD caddy into CD drive 1. Make sure that the label is up and the arrow on the caddy is forward.
26. Press the "activate CD" button. The version number will be displayed in the CD drive Allocation box. The version should read V3.0.
27. Press the "installation" button under "DIS."
28. A box will appear that will ask you to input a password. The password that must be entered is the last five digits of the dealer number that you input. For example: If the dealer number that you entered was 012345, the password that you must enter is 12345.
29. A DIS installation box will now appear. Press "OK." The cursor will be displayed as an hourglass and "x" will fill the box until the loading is complete. When loading is complete, press "OK."
30. Press "END" at the top of the screen and then press "quit." The DIS program CD must remain in the drive.
31. Press the "administration" button and select CD drive 2 in the dialog box.
32. Insert the TIS CD (11/94) with its caddy into CD drive 2. The arrow must be forward and the clear window up.
33. Press "activate CD." The version number of the CD will be displayed. The latest TIS CD is 11/94 V2.1.
34. Press "installation" then "OK." The cursor will again be displayed as an hourglass and "X" will fill the box. The TIS installation procedure will take between two and three hours.
35. When loading is complete, press "OK."
36. Then press "end" and "quit." The TIS CD must remain in the drive.