Computers and Control Systems: Technical Service Bulletins

• Customer Interest
  • Engine - MIL ON/Codes Set/Tapping/Rattling Noise
• By Symptom
  • Customer Interest
    • Engine - MIL ON/Codes Set/Tapping/Rattling Noise
  • Noise
    • Engine - MIL ON/Codes Set/Tapping/Rattling Noise
• All Technical Service Bulletins
  • Computers, Controls - Programming VS Veh. Data Status
  • Compuetrs/Controls - Recommended Diagnostic Procedures
  • Computers - ISTA Diagnosis On Vehicles Prior To E46
  • Computers/Control - Loading/Activation Of Enabling Codes
  • Updated MoDic(R) Diagnostic Software - D12.0
  • Updated MoDic(R) Software - P11.0 Programming
    • Overview
    • Program Highlights
    • Flash Programming Features
    • Programming the Control Module
      • Overview
      • 1. Determine Customer Service Measures
      • 2. Exchange Control Module
      • 3. Exchange EPROM
      • 4. Adjustment EWS - DME Vehicles From 1/95
      • 5. Clear Adaptation Values
    • Diskette Contents
    • How to Load V11.0 Software With MODIC Station
    • Label Printing
    • Prerequisites For Programming
    • Parts Information
  • MoDic(R) - Loss of Program
  • Cable Adapter For ELO Stecker Control Module
  • ELO Diagnostic Cable - New Special Tool
  • MoDic(R) - Update Program
  • Engine - MIL ON/Codes Set/Tapping/Rattling Noise
  • Undefined MoDic(R) Software
    • Overview
    • How to Load C7.0 Software With the MODIC Station
  • Updated MoDic(R) Software - P8.0 Programming
    • Overview
    • Engine Control Module Flash Programming Features
    • Programming the Control Module
      • Overview
      • 2. "Exchange Control Module"
      • 3. "Exchange EPROM"
      • 4. "Adjustment EWS - DME Vehicles From 1/95"
      • 5. "Clear Adaptation Values"
    • How to Load V8.0 Software With the Modic Station
    • Label Printing
    • Prerequisites For Programming
  • Updated MoDic(R) Software - C9.0 ZCS Coding
    • Overview
    • How to Load C9.0 Software With the MODIC Station
    • Label Printing
  • Updated MoDic(R) Software - P9.0 Programming
    • Overview
    • Flash Programming Features
    • Programming the Control Module
      • Overview
      • 1. "Determine Customer Service Measures"
      • 2. "Exchange Control Module"
      • 3. "Exchange EPROM"
      • 4. "Adjustment EWS - DME Vehicles From 1/95
      • 5. "Clear Adaptation Values"
    • How to Load V9.0 Software With the MODIC Station
    • Label Printing
    • Prerequisites For Programming
  • TIS - Software Update 12/96
    • Overview
    • TIS Loading Instructions For DIS Tester
    • TIS Loading Instructions For EPC/TIS Server
    • Proper Care of CDs
      • Overview
      • CD Return Procedure
  • New Special Tool - MoDic(R) Replacement Cable
  • Electrical/Electronic Systems - Troubleshooting Hints
    • Overview
    • Verify the Complaint and Verify the Complaint Is A Malfunction
    • Systematic Troubleshooting
    • Inputs, Processing, and Outputs
    • Common Sense Hints
  • Engine - M42 Production Changes
    • Overview
    • Knock Control
    • Important Note:
    • Crankcase Venting
    • Spark Plug
    • Three Way Catalytic Converter
    • Technical Data
  • Emissions - On-Board Diagnostic Code Updated List
  • Engine Control Module - Diagnostic Software 10.0
  • ECM - Codes and Hardware Numbers
  • Special Tools - Simulator Tool For Bosch Oxygen Sensors
    • Overview
    • Individual Parts of the Simulator
    • Operator Control/ Panel of Simulator
    • Connecting the Simulator
    • Test 1: Oxygen Sensor Testing
    • Test 2: Oxygen Sensor Voltage
    • Test 3: Simulation of Probe Voltage
  • Tools - Seal Pliers For Speedometer Sender