Removed Parts For Transmission With Hydraulic Control E18/2, Overview
Removed parts for transmission with hydraulic control E18/2, overview, 01V, 5 Spd. A/T AWD
1 - Drain plug - 40 Nm
^ With seal
^ Always replace
^ 5 mm socket-head bolt
^ Remove to drain ATF
2 - Bolt - 10 Nm
^ Tighten bolts for oil pan in several stages in diagonal sequence
3 - Oil pan
^ Removing and installing
4 - Gasket
^ Always replace
5 - Oil strainer
^ Removing and installing
6 - Bolt - 8 Nm
^ For mounting valve body: 16 bolts M6 x 60
^ Observe tightening sequence
7 - Valve body
^ Removing and installing
^ Allocation according to transmission code letters
8 - Bolt - 8 Nm
9 - Bracket
^ For wiring harness
^ Hook in wiring harness
^ Mounted with valve body bolts
10 - Bolt - 6 Nm
11 - Transmission Vehicle Speed Sensor (VSS) -G384- (also designated as Sender for transmission output RPM -G195-)
^ Removing and installing
12 - Spacer sleeve
^ Height: 8 mm
13 - Inner oil line
^ Always replace
^ Removing and installing
14 - O-ring
^ Always replace
15 - Speedometer Vehicle Speed Sensor (VSS) -G22-
^ Removing and installing
16 - O-ring
^ Always replace
^ Coat with gear oil and insert
17 - Multi-Function Transmission Range (TR) Switch -F125-
^ Removing and installing
^ Replacing shift rod sealing ring
18 - Bolt - 8 Nm
19 - O-ring
^ Always replace
^ Coat with ATF and insert
20 - Locking clamp
^ Always replace
21 - Wiring harness in transmission
^ Always replace
^ Transmission Fluid Temperature Sensor -G93- is integrated into the wiring harness
^ Remove and install valve body to replace
^ Unhook from bracket for wiring harness, item 10
^ Installation position wiring harness connector: Flat part of rear collar points toward oil pan, the tabs at collar are horizontal
22 - Bolt - 9 Nm
23 - Sensor for transmission RPM -G182-
^ Removing and installing
24 - Connector
^ Is connected at wiring harness in transmission
^ Must be disconnected before removing the valve body
25 - Bolt - 6 Nm
26 - Bracket
^ For solenoid valve
27 - Pressure Control Valve 1 for Auto. Transmission -N215-
^ With O-ring
^ Remove and install valve body
28 - Solenoid valve 3 -N90-
^ Without O-ring
^ Remove and install oil pan
29 - Solenoid valve 2 -N89-
^ Without O-ring
^ Remove and install oil pan
30 - Bolt - 6 Nm
31 - Bracket
^ For solenoid valves
32 - Pressure Control Valve 3 for Auto. Transmission -N217-
^ With O-ring
^ Remove and install oil pan
33 - Pressure Control Valve 4 for Auto. Transmission -N218-
^ With O-ring
^ Remove and install oil pan
34 - Pressure Control Valve 2 for Auto. Transmission -N216-
^ With O-ring
^ Remove and install oil pan
35 - Solenoid valve 1 -N88-
^ Without O-ring
^ Remove and install oil pan and unbolt guide plate for park locking mechanism
^ When installing, do not tighten bolts for guide plate (23 Nm) in selector lever position "P".
36 - Bolt - 6 Nm
37 - Magnet
^ 4 pieces in the oil pan recesses
^ Clean after every removal of oil pan
^ Ensure full surface contact in oil pan
38 - O-ring
^ Always replace
39 - ATF check plug - 80 Nm
^ 17 mm socket-head bolt