Oil Pan, Oil Strainer and Valve Body

Oil pan, oil strainer and valve body, removing and installing

CAUTION! Do not run engine or tow vehicle with removed oil pan or without ATF.

Note:
^ The components shown in the following illustrations can be removed with the transmission installed.
^ Always replace contaminated or malfunctioning valve body.
^ Observe rules for cleanliness when working on automatic transmissions, Refer to Service Precautions.
^ General repair instructions.
^ Thinly lubricate O-rings and seals with Vaseline. Other greases can lead to malfunctions in the hydraulic system of the transmission.





1. Drain plug - 12 Nm (9 ft. lbs.)
^ Socket head plug 5 mm
2. Seal
^ Always replace.
3. Bolt- 10 Nm (7 ft. lbs.)
^ Tighten bolts for oil pan in several steps diagonally.
4. Oil pan
^ Removing and installing, Refer to Oil Pan Removing and Installing.
5. Seal
^ Always replace.
6. ATF screen
^ Removing and installing, refer to ATF Screen, Rmoving and Installing.
7. O-ring
^ Always replace.
^ Lubricate with Vaseline
8. Bolt- 8 Nm (71 inch lbs.)
^ To secure valve body: 5 bolts M6 x 30, 1 bolt M6 x 55 (chromates), 15 bolts M6 x60
^ Observe tightening sequence, Refer to Specifications.
9. Valve body
^ Removing and installing, Refer to Valve Body, Removing and Installing.
10. O-ring
^ Always replace.
^ Lightly lubricate with Vaseline
11. Speedometer - Vehicle Speed Sensor (VSS) -G22
^ Replacing, refer to Speedometer - Vehicle Speed Sensor.
12. Sender for - transmission output RPM - G195
^ Replacing, Refer to Sender for Transmission Output RPM, Removing and Installing.
13. Seal for selector lever shaft
^ Removing and installing, Refer to Selector Shaft Seal, Removing and Installing.
14. Selector shaft
^ To remove, remove spring pin item 15.
15. Spring pin
16. Multi-Function Transmission Range (TR) Switch -F125
^ Replacing, Refer to Multi-Function Transmission Range Switch.
17. Bolt - 8 Nm (71 inch lbs.)
18. Bracket for cable of TR switch
^ Secured with bolts for TR switch
19. Bolt - 5 Nm (44 inch lbs.)
20. Bracket for solenoid valves
^ Must be removed when replacing solenoid valves
21. Solenoid Valve 3- N9O
^ Without O-ring
^ To replace remove oil pan
22. Solenoid Valve 2 - N89
^ Without O-ring
^ To replace remove oil pan
23 - Solenoid Valve 1 - N88
^ Without O-ring
^ To replace remove oil pan
24. Pressure - regulating valve -5- N233
^ With O-ring
^ When installing, lightly lubricate O-ring with Vaseline.
^ To replace remove oil pan
25. Pressure - regulating valve -2- N216
^ With O-ring
^ When installing, lightly lubricate with Vaseline.
^ To replace remove oil pan
^ Removing and installing
26. Pressure - regulating valve -3- N217
^ With O-ring
^ When installing, lightly lubricate with Vaseline.
^ To replace remove oil pan
^ Removing and installing
27. Pressure - regulating valve -4- N218
^ With O-ring
^ When installing, lightly lubricate with Vaseline.
^ To replace remove oil pan
^ Removing and installing
28. Pressure regulating valve -1- N215
^ With O-ring
^ When installing, lightly lubricate with Vaseline.
^ To replace remove oil pan
^ Removing and installing
29. O-ring
^ Always replace.
^ When installing, lightly lubricate with Vaseline.
30. Spacer
^ Height: 8.7 mm
31. Sensor for - transmission RPM -G182
^ Replacing
32. Bolt- 5 Nm (44 ft. lbs.)
33. Wiring - harness inside transmission
^ ATF Temperature Sensor -G93 integrated in wiring harness.
^ Removing and installing
34. Bolt for ATF screen - 5 Nm (44 inch lbs.)
35. O-ring
^ Always replace.
^ When installing, lightly lubricate with Vaseline
36. Circlip
^ Replace if damaged
37. Magnet
^ 4 in recesses of oil pan
^ Clean
^ Be sure magnet makes complete contact with oil pan.
38. O-ring
^ Always replace.
39. ATF filler plug - 80 Nm (59 ft. lbs.)
^ Socket head plug 17 mm